Hot tub owners in Portland OR have over the years been mentored to either replace or sell their Jacuzzi which are not properly functioning. The removal process is not as hard as installing a new one but should be well planned so that you properly undertake your unwanted hot tub removal procedure. The work involved is usually half that of the installation process.
You should assess the state in which your tub is in so that you decide whether to replace or repair it. It is because most removals have discovered catastrophic matters of maintenance and fixing. People in the cool areas are the most affected because they fail to winterize the tubs leading to water freezing in the pipes. Hence, it is important to first get to know the condition of the bath so that you judge which remedy action to take.
The manual from the manufacturer should come in handy during the removal of unwanted sauna baths. Re-reading it will remind you of all the aspects of the spa pool and how it was constructed. It makes you familiar with the electrical system, how the heater was put up and many other issues. Following the manual to the latter will ensure that you avoid any health hazard that may lurk around.
A good number of people own whirlpools that are connected electrically and some may be of high voltage. Electrical needs should be greatly considered before disconnecting any wires. The standard bath should have a central disconnection box to allow you to isolate power. If you will not be replacing your plunge bath, then seal the box so that it will be easy to make future connections during another installation.
The next thing to do is to embark on the actual removal procedure. You will have to unplug the electrical connections including the gas connections, electricity and the heating systems. Here, it is safe to make sure that this is properly done because you can accidentally shock yourself while cutting the electric lines with your saw.
After dealing with the electrical disconnection process, remove the spa skirt. Some whirlpools are manufactured using components connected using screws. This makes it possible for you to disassemble them using a screw driver. Some of the spa slats are connected together via the tongue and groove which do not require as much effort because their removal require no cutting.
Breaking the plunge pool floor is the most difficult part of removing an unwanted hot bath. The durable materials used in their production makes it quite difficult to cut them into smaller pieces. The most convenient tool to use to cut the spa bath is a jigsaw. You should make sure you are well geared up for the job because cutting may be very messy as a lot of dust is produced.
Cutting the Jacuzzi into smaller pieces makes their carriage from the house to the yard easy. It is important that you properly dispose them in a dumpster to keep the environmental effect at the low. It is significant you put on gloves and goggles so that you avoid causing injuries to your hand and keeping dust away from your eyes respectively.
You should assess the state in which your tub is in so that you decide whether to replace or repair it. It is because most removals have discovered catastrophic matters of maintenance and fixing. People in the cool areas are the most affected because they fail to winterize the tubs leading to water freezing in the pipes. Hence, it is important to first get to know the condition of the bath so that you judge which remedy action to take.
The manual from the manufacturer should come in handy during the removal of unwanted sauna baths. Re-reading it will remind you of all the aspects of the spa pool and how it was constructed. It makes you familiar with the electrical system, how the heater was put up and many other issues. Following the manual to the latter will ensure that you avoid any health hazard that may lurk around.
A good number of people own whirlpools that are connected electrically and some may be of high voltage. Electrical needs should be greatly considered before disconnecting any wires. The standard bath should have a central disconnection box to allow you to isolate power. If you will not be replacing your plunge bath, then seal the box so that it will be easy to make future connections during another installation.
The next thing to do is to embark on the actual removal procedure. You will have to unplug the electrical connections including the gas connections, electricity and the heating systems. Here, it is safe to make sure that this is properly done because you can accidentally shock yourself while cutting the electric lines with your saw.
After dealing with the electrical disconnection process, remove the spa skirt. Some whirlpools are manufactured using components connected using screws. This makes it possible for you to disassemble them using a screw driver. Some of the spa slats are connected together via the tongue and groove which do not require as much effort because their removal require no cutting.
Breaking the plunge pool floor is the most difficult part of removing an unwanted hot bath. The durable materials used in their production makes it quite difficult to cut them into smaller pieces. The most convenient tool to use to cut the spa bath is a jigsaw. You should make sure you are well geared up for the job because cutting may be very messy as a lot of dust is produced.
Cutting the Jacuzzi into smaller pieces makes their carriage from the house to the yard easy. It is important that you properly dispose them in a dumpster to keep the environmental effect at the low. It is significant you put on gloves and goggles so that you avoid causing injuries to your hand and keeping dust away from your eyes respectively.
About the Author:
If you are in need of information about unwanted hot tub removal, go to the web pages online here today. Additional details are available at http://www.nwspecialtymoving.com now.
No comments:
Post a Comment